CUSTOMIZED FINNED COILS

-
The long-term use of any item can not be separated from the care and maintenance. Murphy laser welding fin tube is no exception. So what are the specific aspects of fin tube maintenance?
Generally, when water is used for circulation at the beginning of operation, there may be slight leakage. When the temperature rises to the sterilization temperature, the leakage will disappear by itself. If the leakage does not stop, the finned tube must be compressed a little more. If it is still ineffective, it is necessary to open and check the rubber gasket. It is also possible that the finned tubes are arranged in the order of numbers on the fins, which should be corrected.
  1. Regularly check whether the finned tubes are complete, whether there are deposits, coking, rust layer and other scaling adhesion, and clean them immediately. At the same time, it is also necessary to check whether the adhesion between each fin tube and the rubber washer is tight, and whether the rubber washer itself is in good condition, so as to avoid leakage caused by rubber washer degumming and damage.
  1. The plate heat exchanger pressing nut and upper and lower guide rods shall be lubricated with lubricating grease frequently.
  1. Each instrument shall be regulated by a specially assigned person and operated and maintained in strict accordance with the operating procedures.
  1. When the rubber gasket needs to be replaced or the degummed part needs to be repaired, the finned tube shall be removed and placed on the table, and the old gasket shall be removed, or the glue traces in the groove of the finned tube shall be wiped out with fine sandpaper at the degumming position, and then the oil traces in the groove shall be wiped out with carbon tetrachloride or trichloroethylene, and then the back of the new rubber gasket shall be wiped out with fine sandpaper, similarly with carbon tetrachloride or trichloroethylene The alkene solvent wiped out the oil. Then, apply a thin layer of glue on the back of the groove and rubber washer. Let it dry a little, but it still sticks. That is to say, the rubber washer is embedded in the groove, flattened around, and coated with a layer of talcum powder. Then install the fin tube and clamp it gently. According to the glue instructions, it can be used after a period of time.
  1. When recompressing the laser welded composite fin tube, pay attention to the scale position during the last compression. Do not over press the rubber gasket, so as to reduce the service life of the gasket.
  1. When replacing the rubber gasket of the finned tube, it is necessary to update all the segments so as to avoid uneven clearance between the fins and affect the heat transfer effect.

评论

发表评论

此博客中的热门博文

Everything you should know about U bend tube

-
图片
  Murphy can make  U bend tube  in our factory according to customer requirements. The elbow is heat treated according to the customer’s requirements, and then hydrostatic pressure test and dye penetration test are performed as needed. U-shaped elbows are widely used in  heat exchanger  systems. Heat exchanger equipment based on stainless steel U bend tube plays an important role in the nuclear industry and petrochemical machinery manufacturing. U bend tube heat exchangers are specially designed for high temperature applications, especially steam condensing or hot oil systems. When the differential expansion makes the fixed tube-sheet heat exchanger unsuitable, and in some cases the floating head type (HPF) cannot be selected, the U bend tube heat exchanger will be selected. The surface of the finished U-shaped elbow should be free from scale and scratches after bending. Dimensional tolerance U-bend pipes are in accordance with relevant regulations of TEMA R.C.B. and ASTM A566 and ASTM
阅读全文

Finned tube as a heat exchange element exhibits excellent performance indicators

-
图片
Finned tube is a kind of heat exchange element, which is often used in high temperature and flue gas space. In daily life, such as boilers, finned tubes need to be used for heat exchange execution. In such a harsh environment During daily operations, the finned tube itself is required to have corrosion resistance and stability. The finned tube is a typical heat exchange element, in order to improve the heat exchange efficiency, usually by adding fins on the surface of the heat exchange tube to increase the outer surface area of ​​the heat exchange tube, so as to improve the heat exchange For the purpose of efficiency, such a heat exchange tube. Finned tubes work under high-temperature flue gas conditions for a long time. For example, finned tubes for boiler heat exchangers are used in harsh environments, high temperature and high pressure and in corrosive atmosphere, which requires finned tubes to have high performance indicators. For example, excellent corrosion resistance. Many tim
阅读全文

CLASSIFICATION OF HEAT EXCHANGER ACCORDING TO THE HEAT TRANSFER MATERIAL, SURFACE SHAPE AND STRUCTURE

-
图片
1. Metal material heat exchanger Common materials are carbon steel, alloy steel, copper and copper alloy, aluminum and aluminum alloy, titanium and titanium alloy. Because the thermal conductivity of metal material is large, the heat transfer efficiency of this kind of heat exchanger is high. 2. Non-metallic material heat exchanger Commonly used materials are graphite, glass, plastic, ceramics, etc. Because of the small thermal conductivity of nonmetallic materials, the heat transfer efficiency of this type of heat exchanger is low. Often used in corrosive systems. hashtag www.murphyfinnedtubes.com 1. Tube heat exchanger A heat exchanger that conducts heat through a tube wall. It can be divided into shell heat exchanger, coil heat exchanger, tube heat exchanger, fin heat exchanger and so on. 2. Plate heat exchanger A heat exchanger that conducts heat through a plate surface. According to the structural form of heat transfer plate can be divided into plate type, spiral plate
阅读全文